The assembly video will be here soon. Until then, the PDF takes you through all fifteen steps.
BunnyBox Plus assembly video
The Plus has a divider and three doors. The video shows you exactly in which order they go in.
All instructions
BunnyBox Plus
BunnyBox Plus instructions
The BunnyBox Plus comes as a self-assembly kit. The column is put together in 30 to 60 minutes, not counting anchoring. Watch the assembly video first, keep the PDF beside you and then work through the fifteen steps.
Start with the video
In a few minutes, the video shows what the instructions describe in fifteen steps. Especially with the divider, the three doors and the flap assembly, watching is quicker than reading.
Step by step
The same numbering as in the PDF, so you can use the two side by side. Read through all the steps once before you start.
-
01
Back panel and left side panel
Lay the back panel (3) flat, with the edge with screw holes towards you: that is the bottom. Stand the left side panel (1) upright against the left edge. Note: the guides on the inside face upwards and inwards. Fix it with 3 screws A.
Work on a blanket so the coating doesn't get scratched. Using a cordless screwdriver? Set a low torque, as overtightening damages the screw holes.
-
02
Right side panel
Repeat on the right with side panel (2) and 3 screws A. Here too, the guides on the inside face upwards and inwards.
Holes don't line up? Then the panel is the wrong way round.
-
03
Slide in the front frame
Leave the body lying on its back. Slide the front frame (4) in from the bottom between the side panels until it sits against the top edge.
Keep the panels tight together: there must be no gap.
-
04
Fit the bottom panel
Fit the bottom panel (6) at the bottom, into the clips of the side panels. Stand the body upright and screw the bottom in from the inside with 4 screws A at the corners.
-
05
Fit the top panel
Place the top panel (5) with the thick, double-folded edge at the front. Press it flat and screw it to the side panels from the inside with 4 screws A.
-
06
Fit the divider
Slide the divider (9) in from the front into the top compartment, onto the edge above the parcel opening, and press it down. Fix it at the back with 1 screw A into the back panel.
-
07
Letter flap into the letter door
Insert the pins of the letter flap (7) into the holes on the inside of the letter door (8), behind the letter slot.
The flap must swing freely inwards.
-
08
Fit the locks
Fit a lock in the letter door (8) and one in the parcel retrieval door (11). Push the lock through the hole from the outside. On the inside, tighten the large nut. Fit the cam on the square end, bent end facing away from the door, and tighten the small nut.
Turn the key to locked: the cam must hook behind the frame.
-
09
Hang the letter door
Slide a plastic washer E onto a door pin F and insert the pin into the hole in the frame edge below the letter compartment. Place the letter door (8) on the pin with the hole in its underside. Push in the spring pin on top of the door, line the door up against the frame and let the pin slide into the hole in the frame.
Doors already fitted? Go to step 11.
-
10
Hang the parcel retrieval door
Do the same with the parcel retrieval door (11): slide the second washer E onto the second door pin F, insert the pin into the hole in the bottom edge of the frame and place the door on top. Push in the spring pin and let it slide into the hole at the top.
-
11
Bend the flap wings
Bend both wings of the flap wings (13) until they are at a right angle (90°), as shown in the drawing. Bend them both by the same amount.
-
12
Flap wings onto the parcel entry door
Lay the parcel entry door (10) face down on the blanket. Place the flap wings (13) on it as shown. Push the tabs of (10) through the slots in (13) and fold them flat so everything is held firmly.
-
13
Inner panel and connecting bars
Connect the inner panel (12) to the wings of (13) with the 2 connecting bars (14). At the holes in the wings: bolt B with nut D, bolt head on the inside. At the inner panel: bolt C with nut D, bolt head on the outside.
Don't overtighten: the bars must be able to pivot.
-
14
Fit the flap assembly
Place the flap assembly in the middle compartment. First insert pins a and b of the inner panel (12) into the holes of the brackets at the back, then pins c and d of the parcel entry door (10) into the holes at the sides.
-
15
Anchor it to the floor
Place the box on a flat, solid floor (concrete, or tiles on concrete) and check it with a spirit level. Drill through the 4 holes in the bottom: Ø 12 mm, about 100 mm deep, and vacuum up the dust. Insert the 4 expansion bolts G and tap them in with a hammer until the washer rests on the bottom. Tighten the nuts firmly with a 13 mm spanner.
Always anchor the box: unanchored, it can tip over or be taken away. Watch out for pipes and cables when drilling.
Preparation, parts and care
Before you start
- Easier with 2 people
- Allow 30 to 60 minutes, not counting anchoring
- Work on a blanket so nothing gets scratched
- Read all the steps first
- Choose the spot first: a flat, solid floor (concrete, or tiles on concrete), easy for couriers to see, with room to open the flap and the door
- Assemble the box close to that spot
- Lay the carton flat on a blanket, logo facing up, open it and lift off the lid
- Place everything on the blanket, check it against the parts list and keep the packaging until you have finished
- Something missing or damaged? Stop and get in touch with us
Tools
- Assembly: Phillips screwdriver (PH2) or cordless screwdriver
- Assembly: scissors and a blanket
- Anchoring: hammer drill with Ø 12 mm masonry bit
- Anchoring: hammer, 13 mm spanner, pencil and spirit level
- Using a cordless screwdriver? Set a low torque, as overtightening damages the screw holes
In the box
- 1x left side panel (1)
- 1x right side panel (2)
- 1x back panel (3)
- 1x front frame (4)
- 1x top panel (5)
- 1x bottom panel (6)
- 1x letter flap (7)
- 1x letter door (8)
- 1x divider (9)
- 1x parcel entry door (10)
- 1x parcel retrieval door (11)
- 1x inner panel (12)
- 1x flap wings (13)
- 2x connecting bar (14)
Fixings
- A: 15x self-tapping screw
- B: 2x bolt M5 x 20
- C: 2x bolt M5 x 10
- D: 4x nut M5
- E: 2x plastic washer
- F: 2x door pin
- G: 4x expansion bolt
- 2x lock: cylinder, large nut, cam, small nut and 2 keys
- All screws, bolts and washers are used: nothing is left over
Care
- Clean the box with water and mild soap, no abrasives
- Spray the hinges and lock with silicone spray once a year
- Keep the spare key in a safe place
Stuck?
How is it different from the other models?
The Plus is the only model with separate compartments. Letters go through the letter flap into the top compartment, parcels through the parcel entry door into the middle compartment. You take them out through the parcel retrieval door. The divider from step 6 makes that difference.
The front frame won't go in
Leave the body lying on its back and slide the front frame (4) in from the bottom between the side panels until it sits against the top edge. Keep the side panels tight against the back panel: if they spread apart, the frame jams. See step 3.
One of the doors doesn't close flush
Check that the divider (9) is pressed down properly and that the front frame is pushed all the way in. Also check that the spring pin sits in the hole at the top of the frame (steps 9 and 10). Then loosen the frame screws by a quarter turn, straighten the door and tighten them again.
How do I secure the column to the ground?
The fixings include 4 expansion bolts (G). Use them to anchor the box into a concrete floor or into tiles on concrete: drill 4 holes of Ø 12 mm and about 100 mm deep, see step 15. On a soft surface, use a ground anchor or a concrete paving slab under the base.
I have screws left over
That shouldn't happen: with the Plus, all screws, bolts and washers are used. If you have anything left over, go back through the steps and check that every panel is secured at all points. If something is missing instead, get in touch with us.
Can I do this on my own?
You can, but it is easier with 2 people. Especially when standing the box upright and fitting the flap assembly, a second pair of hands is handy.
Can't work it out, or is a part missing? Stop assembling and call +31 85 050 9060 or email contact@bunnyboxshop.com. Have your order number to hand and send us a photo of the step where you're stuck, so we can take a look straight away. You can also let us know via the service form.